|
The Baker rifle (officially known as the Pattern 1800 Infantry Rifle) was a flintlock rifle used by the Rifle regiments of the British Army during the Napoleonic Wars. It was the first standard-issue, British-made rifle accepted by the British armed forces. The Baker Rifle was first produced in 1800 by Ezekiel Baker, a master gunsmith from Whitechapel. The British Army was still issuing the Infantry Rifle in the 1830s. ==History and design== The British army had learned the value of rifles from their experience in the American Revolutionary War. However, existing rifle designs were considered too cumbersome, slow-firing, fragile or expensive to be put to use on any scale beyond irregular companies. Rifles had been issued on a limited basis and consisted of parts made to no precise pattern, often brought in from Prussia. The war against Revolutionary France resulted in the employment of new tactics, and the British Army responded, albeit with some delay. Prior to the formation of an ''Experimental Rifle Corps'' in 1800, a trial was held at Woolwich by the British Board of Ordnance on 22 February 1800 in order to select a standard rifle pattern; the rifle designed by Ezekiel Baker was chosen. During the trial, of the twelve shots fired eleven were placed in a circular target at a distance of . Colonel Coote Manningham, responsible for establishing the Rifle Corps, influenced the initial designs of the Baker. The first model resembled the British Infantry Musket, but was rejected as too heavy. Baker was provided with a German Jäger rifle as an example of what was needed. The second model he made had a .75 calibre bore, the same calibre as the Infantry Musket. It had a 32-inch barrel, with eight rectangular rifling grooves; this model was accepted as the Infantry Rifle, but more changes were made until it was finally placed into production. The third and final model had the barrel shortened from 32 to 30 inches, and the calibre reduced to .653, which allowed the rifle to fire a .625 calibre carbine bullet, with a greased patch to grip the now-seven rectangular grooves in the barrel. The rifle had a simple folding backsight with the standard large lock mechanism (initially marked 'Tower' and 'G.R.' under a Crown; later ones after the battle of Waterloo had 'Enfield'), with a swan-neck cock as fitted to the 'Brown Bess.' Like the German Jäger rifles, it had a scrolled brass trigger guard to help ensure a firm grip and a raised cheek-piece on the left-hand side of the butt. Like many rifles, it had a 'butt-trap' or patchbox where greased linen patches and tools could be stored. The lid of the patchbox was brass, and hinged at the rear so it could be flipped up. The stocks were made of walnut and held the barrel with three flat captive wedges. The rifle also had a metal locking bar to accommodate a 24-inch sword bayonet, similar to that of the Jäger rifle. The Baker was 45 inches from muzzle to butt, 12 inches shorter than the Infantry Musket, and weighed almost nine pounds. As gunpowder fouling built up in the grooves the weapon became much slower to load and less accurate, so a cleaning kit was stored in the patch box of the Baker; the Infantry Muskets were not issued with cleaning kits. After the Baker entered service, more modifications were made to the rifle and several different variations were produced. A lighter and shorter carbine version for the cavalry was introduced, and a number of volunteer associations procured their own models, including the Duke of Cumberland's Corps of Sharpshooters, which ordered models with a 33-inch barrel, in August 1803. A second pattern of Baker Rifle was fitted with a 'Newland' lock that had a flat-faced ring neck cock. In 1806, a third pattern was produced that included a 'pistol grip' style trigger guard and a smaller patchbox with a plain rounded front. The lock plate was smaller, flat, and had a steeped-down tail, a raised semi-waterproof pan, a flat ring neck cock, and a sliding safety bolt. With the introduction of a new pattern Short Land Pattern Flintlock Musket ('Brown Bess') in 1810, with its flat lock and ring-necked cock, the Baker's lock followed suit for what became the fourth pattern. It also featured a 'slit stock'—the stock had a slot cut in its underpart just over a quarter-inch wide. This was done after Ezekiel Baker had seen reports of the ramrod jamming in the stock after the build-up of residue in the ramrod channel, and when the wood warped after getting wet. The rifle is referred to almost exclusively as the "Baker Rifle," but it was produced by a variety of manufacturers and sub-contractors from 1800 to 1837. Most of the rifles produced between 1800 and 1815 were not made by Ezekiel Baker, but under the Tower of London system, and he sub-contracted the manufacture of parts of the rifle to over 20 British gunsmiths. It was reported that many rifles sent to the British Army inspectors were not complete, to the extent of even having no barrel, since the rifle was sent on to another contractor for finishing. Ezekiel Baker's production during the period 1805–1815 was 712 rifles, not even enough to be in the "top ten." The Board of Ordnance, both of its own volition and at the behest of Infantry Staff Officers, ordered production modifications during the rifle's service life. Variations included a carbine with a safety catch and swivel-mounted ramrod, the 1801 pattern West India Rifle (a simplified version lacking a patchbox), the 1809 pattern, which was .75 (musket) calibre, and the 1800/15, which was modified from existing stocks to use a socket bayonet. The most common field modification was the bent stock: riflemen in the field found that the stock was not bent sufficiently at the wrist to allow accurate firing, so stocks were bent by steaming. As this technique produces temporary results (lasting approximately five years), no examples found today exhibit this bend. 抄文引用元・出典: フリー百科事典『 ウィキペディア（Wikipedia）』 ■ウィキペディアで「Baker rifle」の詳細全文を読む スポンサード リンク
|